rescue mode attention please update system again что делать
ERROR MODE Attention! Please update system again.
Breadcrumb
Mohammadreza76646
Member
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page «just a sec. »
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me.
I try to install stock recovery and twrp with adb and huawei multi tools but it didn’t work.
it shows:
«FAILED (remote: partition length get error)»
I try to unbrick my phone too but it shows same message that «FAILED (remote: partition length get error)»
mrmazak
Senior Member
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page «just a sec. »
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me.
I try to install stock recovery and twrp with adb and huawei multi tools but it didn’t work.
it shows:
«FAILED (remote: partition length get error)»
I try to unbrick my phone too but it shows same message that «FAILED (remote: partition length get error)»
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it’s flashed to.
Mohammadreza76646
Member
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it’s flashed to.
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error. )!
And unfortunately my TWRP dos not work anymore
Mohammadreza76646
Member
mrmazak
Senior Member
On the extractor app. On options tab uncheck the verify header option, it should extract then.
Then perhaps first do these three partitions.
Kernel.img
Ramdisk.img
Then
twrp_ramdisk or for stock use recovery_ramdisk
triapoets
Member
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page «just a sec. »
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me.
I try to install stock recovery and twrp with adb and huawei multi tools but it didn’t work.
it shows:
«FAILED (remote: partition length get error)»
I try to unbrick my phone too but it shows same message that «FAILED (remote: partition length get error)»
after all it’s works to me to bypass google account verification
and if now your problem is
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
i solve with re-flash system from this
fastboot flash system system.img
fastboot flash recovery_ramdisk complete_twrp_ramdisk.img
and voila my problem solved..
Mohammadreza76646
Member
On the extractor app. On options tab uncheck the verify header option, it should extract then.
Then perhaps first do these three partitions.
Kernel.img
Ramdisk.img
Then
twrp_ramdisk or for stock use recovery_ramdisk
Hello again dude.
Finally I flashed my phone and I got the system installed.
But now my phones IMEI is lost. and I cant put sim on it.
what should I do now.
FRP is locked! (
mrmazak
Senior Member
So now is locked frp. Does phone have twrp or stock now.?
I think when you tried to install the oreo update for second time, you followed same tutorial as the first time. And that made you problem worse. The tutorial has you flash no-check recovery to 2 partition by block number. 22 & 29. On nougat that is «recovery» and «recovery2». On Oreo partion table it is «reserved2» & «erecovery_vendor»
Link is to rusian language page. Google should translate for you.
Mohammadreza76646
Member
So now is locked frp. Does phone have twrp or stock now.?
I think when you tried to install the oreo update for second time, you followed same tutorial as the first time. And that made you problem worse. The tutorial has you flash no-check recovery to 2 partition by block number. 22 & 29. On nougat that is «recovery» and «recovery2». On Oreo partion table it is «reserved2» & «erecovery_vendor»
Link is to rusian language page. Google should translate for you.
It have stock recovery.
mrmazak
Senior Member
in summery. because i have been going back and forth in multiple different groups, multiple problem, i cant remember it all.
you have broken system, from failed root attempt, followed by failed update.
device condition is as follows.
—system not booting
—stock recovery loads
—fastboot/bootloader loads, but is in frp lock status
options are limited, at best.
I think «dload» method with service rom is best.
other option is maybe paid service like dc-unlock. But I can recall some note on there service about frp-unlock, that can only be used on device with working system. (of course if was working system, wouldn’t need dc-unlock)
Mohammadreza76646
Member
in summery. because i have been going back and forth in multiple different groups, multiple problem, i cant remember it all.
you have broken system, from failed root attempt, followed by failed update.
device condition is as follows.
—system not booting
—stock recovery loads
—fastboot/bootloader loads, but is in frp lock status
options are limited, at best.
I think «dload» method with service rom is best.
other option is maybe paid service like dc-unlock. But I can recall some note on there service about frp-unlock, that can only be used on device with working system. (of course if was working system, wouldn’t need dc-unlock)
No. System boot successfully!
I will send you screenshot:
Mohammadreza76646
Member
Attachments
mrmazak
Senior Member
what about the «about phone» screen
what does it show for version?
If is all stock you should be able to go into deveolper options and enable «oem unlock». If it is greyed out and cannot switch it. Try First to remove google account (all accounts ). and reboot. See if can change then. If not, try Second to do «fastboot oem relock [enter your bootloader code here]
after relock and rebooted oem switch should be enabled again.
****RELOCK IS ONLY ADVISED IF 100% STOCK ROM****
otherwise relock could make more trouble.
Still not sure how to get IMEI back even if unlocked frp though.
Mohammadreza76646
Member
what about the «about phone» screen
what does it show for version?
If is all stock you should be able to go into deveolper options and enable «oem unlock». If it is greyed out and cannot switch it. Try First to remove google account (all accounts ). and reboot. See if can change then. If not, try Second to do «fastboot oem relock [enter your bootloader code here]
after relock and rebooted oem switch should be enabled again.
****RELOCK IS ONLY ADVISED IF 100% STOCK ROM****
otherwise relock could make more trouble.
Still not sure how to get IMEI back even if unlocked frp though.
Thanks )
I’m so sorry for my posts, it’s because I don’t have a stable connection and I can’t see notification of my thread.
I gave my phone to friend an he fix IMEI (I don’t know how)
But OEM is steel lock.
I think he did it with using special box.
MeChiku
Member
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page «just a sec. »
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me.
I try to install stock recovery and twrp with adb and huawei multi tools but it didn’t work.
it shows:
«FAILED (remote: partition length get error)»
I try to unbrick my phone too but it shows same message that «FAILED (remote: partition length get error)»
HELP! (HARDBRICK)? [Func NO : 11 (recovery image) Error NO : 2 (load failed!)
Breadcrumb
4r44444
Senior Member
Hello, I used relock bootloader command in fastboot. now the phone only restarts to «ERROR MODE»
It looks like that
Attention!
Please Update system again.
Error!
Func NO : 11 (reovery image)
Error NO : 2 (load failed!)
Anybody can help me? When I restart phone this mode appears again and again, can’t enter fastboot mode or recovery.. when pressing any key it restarts to this error mode.
Also phone can’t be tunred off, when hard pressing POWER it will instantly reboot to this mode.
Phone doesn’t show up in device manager. when doing anything via fastboot command only waiting for device.
RobertHarkness
Senior Member
4r44444
Senior Member
RobertHarkness
Senior Member
4r44444
Senior Member
4r44444
Senior Member
Probably if u see this are u already in fastboot try when shows this screen plug cable to pc and write in adb >>>> fastboot devices
Attention!
Please Update system again.
Error!
Func NO : 11 (reovery image)
Error NO : 2 (load failed!)
edit: ok now I see. waiting for device
How happend this situation, what u do before relock bootloader?
The smartphone doesn’t show up in adb-devices. Also dodn’t see it in USB. before I did this it worked without problems.
Honor 10. Помощь в программном ремонте ERROR MODE, COL-L29.
vanya_d
Honor 10. Версия прошивки: COL-L29 10.0.0.185(C10E6R1P4)
Скорее всего превратился в кирпич при обновлении или перепрививки! Точно не известно (.
При любом включении выдает ошибку: ERROR MODE. Attention! Please update system again. Error! Func NO : 20 (flash cert check). Error : 1 (flash device replace illegal).
Так же выдает данную ошибку в Recovery. Но комп его видит. Через TESTPOINT тоже видит.
Не помогло только Board прошивкой удалил imei. Проблема осталась!
Вложения
Alikaaa
Honor 10. Версия прошивки: COL-L29 10.0.0.185(C10E6R1P4)
Скорее всего превратился в кирпич при обновлении или перепрививки! Точно не известно (.
При любом включении выдает ошибку: ERROR MODE. Attention! Please update system again. Error! Func NO : 20 (flash cert check). Error : 1 (flash device replace illegal).
Так же выдает данную ошибку в Recovery. Но комп его видит. Через TESTPOINT тоже видит.
Не помогло только Board прошивкой удалил imei. Проблема осталась!
Honor 10. Версия прошивки: COL-L29 10.0.0.185(C10E6R1P4)
Скорее всего превратился в кирпич при обновлении или перепрививки! Точно не известно (.
При любом включении выдает ошибку: ERROR MODE. Attention! Please update system again. Error! Func NO : 20 (flash cert check). Error : 1 (flash device replace illegal).
Так же выдает данную ошибку в Recovery. Но комп его видит. Через TESTPOINT тоже видит.
Не помогло только Board прошивкой удалил imei. Проблема осталась!
ERROR MODE Attention! Please update system again.
Breadcrumb
marxspawn
Member
make sure you know what you are doing before flashing.
for example. on oreo the boot and recovery share one kernel image. SO if kernel is messed up you will not be able to boot «boot» or «recovery»
mrmazak
Senior Member
you do not fash boot on oreo.
you flash the two separate partitions
marxspawn
Member
you do not fash boot on oreo.
you flash the two separate partitions
Thank you MrMazak, I do appreciate your help.
I have every system file for the BND-L34. I have been using the multi tool and plain old terminal. Nothing was working. As soon as I saw your comment about how Magisk update may patch to the kernel, I remembered that was the last function I did before it stopped working.
IonDEfeso
Member
if you were on oreo. then there is not a boot.img, instaed there is seperate ramdisk.img and kernel.img.
i have all the files already extracted for oreo and a backup from nougat as well.
make sure you know what you are doing before flashing.
for example. on oreo the boot and recovery share one kernel image. SO if kernel is messed up you will not be able to boot «boot» or «recovery»
Well ill be lying if I say I know what im doing haha. I imagine updating the magisk overwrote something it shouldnt have and i broke the phone and now im trying to write back what i wrote with your help. So I downloaded the kernel for oreo in the link you had and now the error page is gone and I even get the RRO booting animation but at the end it just restarts and then boots me to Huawei eRecovery.
So I dont know much but im guessing magisk maybe rewrote something else that doesn’t let me boot? Is there a possibility to re-install magisk through adb? I still have the Magisk_v16.zip one I downloaded specifically for my phone.
If not then how could I just make the phone work again even if it means going back to emui 8.0 (even though i would pref if i could just reinstall the same or any other treble rom)?
Thanks a lot for the help!
mrmazak
Senior Member
Well ill be lying if I say I know what im doing haha. I imagine updating the magisk overwrote something it shouldnt have and i broke the phone and now im trying to write back what i wrote with your help. So I downloaded the kernel for oreo in the link you had and now the error page is gone and I even get the RRO booting animation but at the end it just restarts and then boots me to Huawei eRecovery.
So I dont know much but im guessing magisk maybe rewrote something else that doesn’t let me boot? Is there a possibility to re-install magisk through adb? I still have the Magisk_v16.zip one I downloaded specifically for my phone.
If not then how could I just make the phone work again even if it means going back to emui 8.0 (even though i would pref if i could just reinstall the same or any other treble rom)?
Thanks a lot for the help!
IonDEfeso
Member
I tried flashing the ramdisk and nothing happened. I lost the TWRP when I updated the magisk so only had the Huawei eRecovery which i tried to do a factory reset with and the phone just restarted and now it is stuck in a loop. It doesnt seem to load eRecovery again and dont show the three options it did before in the Phone Unlocked Warning Screen the one that states «Your device has been unlocked and cant be trusted. » now when it gets there it only states «Your device is booting now» then it tries to load RR and reboots.
Not sure what are my options now or if I finally killed the phone.
mrmazak
Senior Member
I tried flashing the ramdisk and nothing happened. I lost the TWRP when I updated the magisk so only had the Huawei eRecovery which i tried to do a factory reset with and the phone just restarted and now it is stuck in a loop. It doesnt seem to load eRecovery again and dont show the three options it did before in the Phone Unlocked Warning Screen the one that states «Your device has been unlocked and cant be trusted. » now when it gets there it only states «Your device is booting now» then it tries to load RR and reboots.
Not sure what are my options now or if I finally killed the phone.
marxspawn
Member
I am in this same boat too, after a magisk update my error mode started.
After you helped me get past the boot/recovery errors, I have been getting the boot loops as well. They are just under 2 min apart ( I have been timing it). I can get through the new phone startup then reboots. Then phone starts I can log in to any os I install (even complete stock and safe mode) and just under 2 min it will reboot.
I have installed the stock recovery to Ramdisk_recovery and completed the factory reset and still loops at just under 2 min. The phone will stay in any recovery without looping. Only loops once a system image is loaded.
I have twrp and two different backups, both will fail because of modem_fw and if I exclude it the restore will complete but the backups will never get past the device is not trusted page.
I am wondering if I will need to do a rollback to nougat then let the device do the Oreo update OTA, but I cannot find a rollback image for this device.
Thanks again for all your help
IonDEfeso
Member
I flashed ramdisk again and the boot loop was gone, not sure if i flashed the wrong one before so it got me there. Anyway it turns out i did had TWRP recovery installed still it just couldnt access it by pressing the regular keys (not sure if it was because i was using this one that is supposed to be for huawei devices (made specifically for mate 9 I think).
Anyway I said screw it after getting into twrp so I followed crayonicle’s guide to getting back to stock Emui and so now im back to stock emui 8.0 but im still planing to soon flash phhusson’s aosp 8.1 rom anyway thanks for all the help i couldn’t have made it without it!
I am in this same boat too, after a magisk update my error mode started.
After you helped me get past the boot/recovery errors, I have been getting the boot loops as well. They are just under 2 min apart ( I have been timing it). I can get through the new phone startup then reboots. Then phone starts I can log in to any os I install (even complete stock and safe mode) and just under 2 min it will reboot.
I have installed the stock recovery to Ramdisk_recovery and completed the factory reset and still loops at just under 2 min. The phone will stay in any recovery without looping. Only loops once a system image is loaded.
I have twrp and two different backups, both will fail because of modem_fw and if I exclude it the restore will complete but the backups will never get past the device is not trusted page.
I am wondering if I will need to do a rollback to nougat then let the device do the Oreo update OTA, but I cannot find a rollback image for this device.
Thanks again for all your help
Do you have a Honor 7x or MATE SE? I have the Mate SE (L34, USA) and downloaded the official L34 Emui 8.0 ROM zip here now I dont know why would that rom be incompatible with Honor 7x since is basically the same phone so long is on the same region I suppose is fine. After that i just followed crayonicle’s guide to getting back to stock Emui.
If for some reason you cant do that then try re-intalling Magisk to other versions i saw this thread that described the problems we had supposedly being fixed by installing Magisk 16.4, I tried re-installing the v16 one and my phone felt that it almost was going to get back to life (the booting stayed a lot longer but then it just got stuck there so). Well thats it all i have to report I hope is of use to you.
marxspawn
Member
I have the mate and thank you, the HuRUpdater worked with the zip files I already had. I changed the names to match the ones it said and everything was fixed. No loops and baseband imei are back.
Thanks for all the help guys!
Ypk2020
Member
Zeroxcar10
New member
Similar threads
Breadcrumb
Top Liked Posts
you do not fash boot on oreo.
you flash the two separate partitions
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page «just a sec. »
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me.
I try to install stock recovery and twrp with adb and huawei multi tools but it didn’t work.
it shows:
«FAILED (remote: partition length get error)»
I try to unbrick my phone too but it shows same message that «FAILED (remote: partition length get error)»
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it’s flashed to.